CVM AND CONVERTIBLE TOP PDF

Bagami The top and frame assembly is bolted to the main top bracket at four points. If you have questions about this VAT, please contact the seller. Please check that your vehicle is in the list and that there are no restrictions for your vehicle in the notes. See other items More The ignition switch must be cycled to clear the fault before the top will again function. Redeem your points Conditions for uk nectar points — opens in a new window or tab. What type of input is provided by the angle hall sensors for top operation?

Author:Kazracage Malagul
Country:Kazakhstan
Language:English (Spanish)
Genre:Love
Published (Last):23 May 2018
Pages:12
PDF File Size:11.11 Mb
ePub File Size:20.48 Mb
ISBN:854-2-51885-601-4
Downloads:27039
Price:Free* [*Free Regsitration Required]
Uploader:Arashit



Tojajas The sensors receive power and ground from the CVM. The greater pressure on the raise side of the piston will overcome the lowering pressure to raise the frame. Add to basket. Skip to main content.

There are three connectors on each side of the top assembly in front of the top stor- age compartment. After completing this module, you should be able to: Click here to sign up. Learn more — opens in new window or tab. How many hydraulic solenoids are used in the operation of the E46iC top? For additional information, see the Global Shipping Programme terms and conditions — opens in a new window or tab.

During znd soft top operation, when the tensioning bow is raised or when the top is in the storage compartment, the CVM signals the GM over the K-Bus to fop the storage com- partment cover. Visit my eBay shop. The signal from the variable storage compartment floor micro switch will prevent the stor- age cover from convretible when the floor is in the open position.

The top LED will flash whenever the top is in operation and not locked to the windshield frame or stored completely in the compartment. S Hall Angle Sensor: Select a valid country. Help Center Convertiblw new research papers in: S Angle Hall sensors: Production E46 Convertibles are not fit- ted with S When the solenoid is energized, hydraulic pres- sure is applied to the raising side of the ram.

The drive mechanisms have been redesigned for smoother operation, however they still are responsible for unlocking the top from the windshield and raising the front of the top past the tension point. It is constructed from aluminum with a finished fabric upholstery on the inside.

Flexible drive shafts are used activate the lock assemblies and drive the tension linkage rods to raise the top past the tension position. It holds pressure in the system when any of the cylinder solenoids are not energized. Which hall sensors control the flashing of the LED in the top switch? Contact the seller — opens in a new window or tab and request a postage method to your location. This listing is for the part or sub-assembly number shown below only. Redeem your points Conditions for uk nectar points — opens in a new window or tab.

Seller assumes all responsibility for this listing. It receives power and ground from the CVM. TOP Related.

INTRODUCTION TO RECONFIGURABLE COMPUTING BOBDA PDF

5 CVM and Convertible Top

Tojajas The sensors receive power and ground from the CVM. The greater pressure on the raise side of the piston will overcome the lowering pressure to raise the frame. Add to basket. Skip to main content. There are three connectors on each side of the top assembly in front of the top stor- age compartment. After completing this module, you should be able to: Click here to sign up.

BELDEN 9914 PDF

Manual download

Help Center Find new research papers in: How many hydraulic solenoids are used in the operation of the E46iC top? Mini Workshop Manuals The frame of the manual top is similar to the fully automatic system, with two piston dampers mounted on the assembly to aid in its operation. Roof rack mounting points are integrated into the top on the left and right sides. The hydraulics hold the position of the top and remain under pressure for approximately 20 minutes if the ignition key is left in the ON position. If the ignition is switched OFF, in the intermediate position, the pressure will be released in steps after approximately 10 seconds until all pressure is drained from the cylinders. There are 1 items available. Operation of the hydraulic cylinders is controlled via final stages and solenoids mounted on the hydraulic unit and top frame.

Related Articles